EVM SE in Black, by Estoque Mods

The EVM is an extremely well built, light weight, and well designed bottom feed mod by Estoque Mods, featuring an original ES design RTS1.0 iVibe Dual MOSFET with haptic feedback via vibration to notify users of low battery issues and lock/unlock status.

This "SE" (Special Edition) version of the EVM features a double-anodized gold/black firing button to differentiate it from previous versions. This new firing button has a black face to subdue it, while featuring a gold anodized bevel for a subtle yet classy accent.

This Black version of the EVM SE features a media blasted matte black anodized finish to minimize fingerprints, setting it apart from the brighter brushed finish of the Gun Metal Grey and Ti Silver  bodies.

Note: Photos shown with atomizer attached are for demonstration purposes only, and are not included in this sale. This sale is only for the mod.

A single 10 mL White SQ Bottle is included with this unit, but additional bottles in different colours can be purchased << HERE >>.

A light weight aluminum sleeve houses the internal components which consists of an integrated battery sled and connector system that contains the MOSFET board. This internal housing is made of light weight but durable and rigid plastic made of a blend of polycarbonate and ABS.

Silver plated electrical wiring contacts and gold plated copper battery contacts ensures solid performance, and capable of delivering the power needed for this RTS 1.0 iVibe Dual MOSFET.

Note: Due to length and gauge of the positive battery contact lead, the EVM experiences a bit more voltage drop compared to comparable mods. Please be aware of this and build accordingly for the limitations of this mod. Recommended build is 0.30 Ohms or higher.

Powered by a single 18650 high drain IMR battery, the RTS 1.0 iVibe Dual MOSFET featured in this mod offers a full suite of safety and status indicators to the user.

EVM Specifications:

• Mod type: Bottom Feed "Squonk" Mod, powered by iVibe MOSFET
• Battery: 1x 18650 high drain IMR
• Dual MOSFET: RTS1.0 - Original Estoque design
• 510 Connector: Manual adjustment ( reverse screw ) via 2.0mm Allen key
• Height: 73.5mm ( at the 510 base )
• Width: 45.5mm
• Thickness: 26mm
• Estoque SQ bottle: 10 mL capacity food grade silicon. Each mod comes with 1 standard clear bottle.
• Spare White (Clear), Black, and Red SQ bottles are optional for your purchase, and includes a sealing cap for pre-filled carry.

RTS 1.0 iVibe Dual MOSFET Features:

• Low resistance (short circuit) protection.
• Support for coils as low as 0.075 Ω.
• Eight second power switch protection. Power cuts off after 8 seconds of continuous firing. This is to protect the device in case of accidental discharge.
• Reverse polarity protection.
• Device lock/unlock for safe carry. Vibrates once to indicate switch lock. Vibrates twice to indicate switch unlock.

Battery Level LED Light Indicator:

• Green LED: 70 - 100%
• White LED: 30 - 70%
• Red LED: 0 - 30%

Power Lock / Unlock:

Press power button 3 times consecutively within 2 seconds to lock/unlock. Vibrates once to indicate lock. Vibrates twice to indicate unlock.

Turn LED Light On / Off during firing (Stealth Mode):

1. Lock the device.
2. Press and hold power button for 3 seconds until LED light flashes white to indicate status change.
3. Unlock for usage.

iVibe Technical Functions:

• Power off (Locked): Vibrates once
• Power on (Unlocked): Vibrates twice
• Low battery indicator: Vibrates 3 times when the voltage has dropped to 30% of total capacity, or below 3.5 Volts. LED turns to RED.
• Power cut off / Power securing: Vibrates 3 times _ RED LED flash 3 times when battery voltage drops to 3.2 Volts. To protect the battery, the chip assumes the battery has discharged at this level, and the device shuts down to protect the cell from a deep discharge.
• Short circuit warning: Red LED flashes 5 times and vibrates twice. No power will output to the 510 connector.

Usage Note: To avoid damaging the bottom of your SQ Bottle, please ensure you connect it to the mod by holding on to the top section of the bottle only. If you push the bottle up from the bottom, against the stainless steel feeder tube, you risk puncturing the bottom of the bottle.

Usage Note: When inserting the battery sled back in to the mod sleeve, ensure you guide the silicone bottle in place, as the bottom edge of the bottle may get caught on the lower edge of the squonk window. This is more likely to occur when the bottle is filled with liquid.

Usage Note: Pay notice to the green silicone o-ring at the bottom of the mod sleeve when you have removed the internal components of the mod. While this o-ring stays reasonably secure in place, there is the possibility of it falling out if the shell is jarred or struck. The mod will still function fine without this o-ring if you happen to lose it, but be aware that the sleeve and the internal components may have a slightly looser fitment as a result. To maintain a rattle-free assembly, try and keep this o-ring in place at all times.

DISCLAIMER: Rebuildable atomizers and mechanical mods are for experienced vapers with access to meters and a working knowledge of Ohms Law, Watts Law, battery safety, and how general electricity works. Please ensure care is taken as to not cause damage nor harm to the atomizer, your battery, the vaping device, yourself, others, or personal property.

Vapes by Enushi is not responsible for misuse of product, or dangerously low coil builds. Vapes by Enushi is not liable for the use of improper batteries for your builds.